型号描述
紧凑型传送 8026 特别适合不含固体的液体，其用途非常广泛（水、废水监控、化学处理...）。可在短型或长型传感器结构中使用带有叶轮式传感器的传送器（取决于所用的接头 DN）。这种指形传感器被一个销钉固定在外壳上。外壳包含电子设备模块和一个可拆下的指示器。设备也可在没有指示器的情况下工作，但为了对传送器进行编程（即数据参数化、标准参数复位、对在读取运行时应该输出的信息进行编程、访问代码、电流输出特性等），同时对测得的和处理的数据进行持续观察，要求存在指示器。8026 型设备的可用部件有：- 2 个可编程的输出端：一个晶体管输出端 (NPN) 和一个 4-20-mA 电流输出端（双线）- 3 个可编程的输出端：两个晶体管输出端 (NPN/PNP) 和一个 4-20-mA 电流输出端（双线）- 4 个可编程的输出端：两个晶体管输出端 (NPN/PNP) 和两个 4-20-mA 电流输出端（三线）8026 型设备能够转换测量信号，以不同尺寸单位显示不同数值（如果已插上显示模块）并计算通过一个或两个 M12 插拔连接器传输的输出信号。传送器具有一个或两个晶体管输出端，能够接通一个电子阀、激活一个警报并借助于一个或两个电流输出端 4-20 mA 建立一个或两个调节回路。
1）PN10、DN15 至 DN400 过程接口
2）可编程的输出端：1 或 2 个晶体管输出端以及 1 或 2 个电流输出端 4-20 mA
3）可拆除的指示器，带有背景照明装置，适合流量和体积，带有两个数量计数器
4）通过 TEACH-IN 自动校准，检查所有无流量输出端
Type Description
The Bürkert transmitter Type 8026 is a compact device, specially designed for measuring the flow rate in solid-free liquids, in a variety of applications (water, waste water monitoring, chemical processing...). The transmitter is equipped of a sensor with paddle-wheel, available in long or short version (depend on DN of used fitting). This sensor holder is plugged-in and pined to an enclosure with cover, containing the electronic module. A removable display completes this transmitter. The flow transmitter can operate without the display, but it will be required for programming the transmitter (i.e. set parameters, restore default parameters, programme information to be displayed, programme access codes, adjust 4-20 mA output(s) ...) and also for visualizing continuously the measured and processed data. The device Type 8026 is available with: - 2 programmable outputs : one transistor output (NPN) and one 4-20 mA current output (2-wire) - 3 programmable outputs: two transistor outputs (NPN/PNP) and one 4-20 mA current output (2-wire) - 4 programmable outputs: two transistor outputs (NPN/PNP) and two 4-20 mA current outputs (3-wire) The device Type 8026 converts the measured signal, displays different values in different units (if display mounted) and computes the output signals, which are provided via one or two M12 fixed connectors. Thanks to 1 or 2 transistor outputs, the transmitter can be used to switch a solenoid valve, activate an alarm and, thanks to 1 or 2 current outputs, establish one or two control loops.
1）PN10, DN15 to DN400 fluidic process connection
2）Programmable outputs : one or two transistor output(s) and single or dual 4-20 mA analog output(s)
3）Removable backlit display of flow and/or two totalized volumes
4）Automatic-calibration: TEACH-IN, simulation of outputs signals provided without the need for real flow
