意大利DUPLOMATIC迪普马轴向柱塞变量泵
VPPL-008PC5-R00S/20N VPPL-016PC5-R00S/20N VPPL-022PC5-R00S/20N
VPPL-036PC5-R00S/20N VPPL-046PC5-R00S/20N VPPL-070PC6-R00S/20N
意大利DUPLOMATIC迪普马轴向柱塞变量泵
VPPL-070PCR-R00S/20N VPPL-100PCR-R00S/20N VPPL-008PQC-R00S/20N
VPPL-016PQC-R00S/20N VPPL-022PQC-R00S/20N VPPL-036PQC-R00S/20N
VPPL-046PQC-R00S/20N VPPL-070PQC-R00S/20N VPPL-100PQC-R00S/20N
VPPL-008PC5-R10S/20N VPPL-016PC5-R10S/20N VPPL-100PQC-R00B/20N
VPPL-022PC5-R10S/20N VPPL-036PC5-R10S/20N VPPL-046PC5-R10S/20N
VPPL-070PC6-R10S/20N VPPL-100PC6-R10S/20N VPPL-008PCR-R10S/20N
液压泵自吸高度不超过500mm(或进口真空度不超过0.03MPa)，若采用补油泵供油，供油压力不得超过0.5MPa，当供油压力超过0.5MPa时，要改用耐压密封圈。对于柱塞泵，应尽量采用倒灌自吸方式。液压泵装机前应检查安装孔的深度是否大于泵的轴伸长度，防止产生顶轴现象，否则将烧毁泵，液压泵使用注意事项。
VPPL-016PCR-R10S/20N VPPL-022PCR-R10S/20N VPPL-036PCR-R10S/20N
VPPL-046PCR-R10S/20N VPPL-070PCR-R10S/20N VPPL-100PCR-R10S/20N
VPPL-008PQC-R10S/20N VPPL-016PQC-R10S/20N VPPL-022PQC-R10S/20N
VPPL-036PQC-R10S/20N VPPL-046PQC-R10S/20N VPPL-070PQC-R10S/20N
VPPL-008PC5-R00B/20N VPPL-070PQC-R00B/20N VPPL-100PQC-R10S/20N
VPPL-016PC5-R00B/20N VPPL-022PC5-R00B/20N VPPL-036PC5-R00B/20N
VPPL-046PC5-R00B/20N VPPL-070PC6-R00B/20N VPPL-100PC6-R00B/20N
VPPL-008PCR-R00B/20N VPPL-016PCR-R00B/20N VPPL-022PCR-R00B/20N
液压泵启动时应先点动数次，油流方向和声音都正常后，在低压下运转5～10min，然后投入正常运行。柱塞泵启动前，必须通过壳上的泄油口向泵内灌满清洁的工作油。 液压泵的工作原理是什么呢？启东高压为您解答！广东轴向液压泵供应
意大利DUPLOMATIC迪普马轴向柱塞变量泵
