绝缘环氧树脂、塑料橡胶体积表面电阻率测试仪使用条件
①环境温度： 0～40℃
②相对温度：≤70%
③供电电流：交流 220V±10%50Hz
绝缘环氧树脂、塑料橡胶体积表面电阻率测试仪主要标准：
GB/T 1410-2006 固体绝缘材料 体积电阻率和表面电阻率试验方法
GB1672-8液体增塑剂体积电阻率的测定
GB 12014 防静电工作服
GB/T 20991-2007 个体防护装备 鞋的测试方法
GB 4385-1995 防静电鞋、导电鞋技术要求
GB 12158-2006 防止静电事故通用导则
GB 4655-2003 橡胶工业静电安全规程
GB/T 1692-2008 硫化橡胶绝缘电阻的测定
GB/T 12703.6-2010 纺织品 静电性能的评定 第6部分 纤维泄漏电阻
GB 13348-2009 液体石油产品静电安全规程
GB/T 15738-2008 导电和抗静电纤维增强塑料电阻率试验方法
GB/T 18044-2008 地毯 静电习性评价法 行走试验
GB/T 18864-2002 硫化橡胶 工业用抗静电和导电产品电阻极限范围
GB/T 22042-2008 服装 防静电性能 表面电阻率试验方法
GB/T 22043-2008 服装 防静电性能 通过材料的电阻(垂直电阻)试验方法
GB/T 24249-2009 防静电洁净织物
GB 26539-2011 防静电陶瓷砖 Antistatic ceramic tile
GB/T 26825-2011 抗静电防腐胶
GB 50515-2010 导(防)静电地面设计规范
GB 50611-2010 电子工程防静电设计规范
GJB 105-1998-Z 电子产品防静电放电控制手册
GJB 3007A-2009 防静电工作区技术要求
GJB 5104-2004 无线电引信风帽用防静电涂料及风帽静电性能通用要求
技术参数
测试电压 （V） 10 50 100 250 500 1000
电阻测量范围 1×104Ω ～1×1018 Ω；
电流测量范围 2×10-4Ａ ～1×10-16Ａ；
①直流高压电流输出 10，50，100，500，1000V 五档
②根据试样的电阻值及直流高压值选择合适的量程倍率。
③高输入阻抗直流放大器（输入阻抗>1015Ω）
④指示仪表，指示被测绝缘电阻。
⑤电源供给仪器各部分工作电源。
安全注意事项
4.1 使用前务必详阅此说明书，并遵照指示步骤，依次操作。
4.2 请勿使用非原厂提供之附件，以免发生危险。
4.3 进行测试时，本仪器测量端高压输出端上有直流高压输出，严禁人体接触 ，以免触电。
4.4 为避免测试棒本身绝缘泄漏造成误差，接仪器测量端输入的测试棒应尽可 能悬空，不与外界物体相碰。
4.5 当被测物绝缘电阻值高，且测量出现指针不稳现象时，可将仪器测量线屏 蔽端夹子接上。 例如：对电缆测缆芯与缆壳的绝缘时，除将被测物两 端分 别接于输入端与高压 端，再将电缆壳 ，芯之间的内层绝缘物接仪器 “G”，以消 除因 表面漏电而 引起的测量误差。也可用加屏蔽盒的方法， 即将被测物置于金属屏蔽盒内，接上测量线。
优点：
体积小、重量轻、准确度高；
的被测电阻、和流过电阻的电流双显示，使操作测量更加方便；
性能稳定、读数方便；
既能测电阻又能测电流；
使用操作简便，在任何电阻量程和测试电压下均直接读显示数字结果，免去要乘以一个系数的麻烦，使测量超高电阻就如用万用表测量普通电阻样简便。
Insulation epoxy resin, plastic rubber surface resistivity tester volume conditions of use
1) ambient temperature: 0 ~ 40 ℃
(2) the relative humidity: 70% or less
(3) power supply current, ac 220 v + 10% for 50 hz
Insulation epoxy resin, plastic rubber volume surface resistivity tester is main criteria:
GB/T 1410-2006 of solid insulating materials Volume resistivity and surface resistivity test method
GB1672-8 liquid plasticizer of volume resistivity measurement
GB 12014 anti-static overalls
GB/T 20991-2007 test method of the individual protective equipment of shoes
GB 4385-1995, anti-static shoes, conductive technical requirements
Prevent electrostatic guide general accident of GB 12158-12158
GB 4655-2003 rubber industrial electrostatic safety procedures
GB/T 1692-2008 vulcanized rubber insulation resistance measurement
GB/T 12703.6 2010 textile electrostatic performance evaluation Part 6 fiber leakage resistance
GB 13348-2009 liquid petroleum products electrostatic safety procedures
GB/T 15738-2008, conductive and antistatic fibre reinforced plastics resistivity test method
GB/T 18044-2008 - carpet static walking behavior evaluation test
GB/T 18864-2002 - vulcanized rubber industry with antistatic and conductive products resistance limit range
GB/T 22042-2008 clothing antistatic performance surface resistivity test method
GB/T 22043-2008 clothing antistatic performance by the resistance of the material (vertical resistance) test method
GB/T 24249-2009, anti-static clean fabric
GB 26539-2011 anti-static ceramic tile Antistatic ceramic tile
Anti-static anticorrosion adhesive GB/T 26825-26825
GB 50515-50515 lead (prevention) electrostatic surface design specification
GB 50611-50611 electronic engineering antistatic design specifications
GJB 105-1998 - Z electronic products electrostatic discharge manual control
GJB 3007 a - 2009 anti-static work area technical requirements
GJB 5104-2004 radio fuze cap with antistatic coatings and cowl electrostatic general performance requirements
Insulation epoxy resin, plastic rubber surface resistivity tester size technical parameters
Test voltage (V) 10 to 50, 100, 250, 500, 1000
Resistance measurement range 1 1 x 1018 x 104 Ω ~ Ω;
Current measurement range 2 x 10-4 a ~ 1 x 10 to 16 a.
1) dc,50,100,500,1000 10 V output current high five
(2) according to the sample resistance and dc high voltage value to choose the appropriate range ratio.
(3) high input impedance dc amplifier (> 1015 Ω) the input impedance
(4), indicating meter indicates measured insulation resistance.
(5) power supply instrument parts work power.
Insulation epoxy resin, plastic rubber surface resistivity tester size security considerations
4.1 be sure to read the manual before use and follow the instructions step, operating in turn.
4.2 do not use the original factory to provide the attachment, thank you for your cooperation.
4.3 during the test, the instrument measuring the dc high voltage output high voltage output, it is strictly prohibited to human exposure, so as to avoid electric shock.
4.4 to avoid test bar insulation leakage error caused by itself, by instrument measuring the input can be hung up test bar, no object collision with the outside world.
Analyte 4.5 when a high insulation resistance, and measure the instability phenomenon appear Pointers, line screen can be measured All the clip connected. For example: the insulation of the cable and cable to cable measured shell, in addition to the analyte to the two end points Don't pick up the input and the high pressure side, and then to a shell, the cable core between inner insulation instruments "G", to eliminate the error of measurement caused by surface leakage. Method can also be used with shielding box, is about to be tested on the metal shielding box, measuring line.
Insulation epoxy resin, plastic rubber surface resistivity tester size advantage:
Small volume, light weight, high accuracy;
Unique resistance being measured, according to the current through the resistor, and double make the measurement more convenient operation;
Stable performance, easy reading;
To measure resistance and current measurement;
Use of simple operation, are directly under any resistance range and testing voltage reading display Numbers as a result, the bother of should be multiplied by a coefficient, makes the measuring high resistance as ordinary resistance is measured with a multimeter sample is simple.
