当前位置：深圳博瑞图电子科技有限公司>>>>全新美国*Microsemi flashpro5 usb线现货-PLC编程器

全新美国*Microsemi flashpro5 usb线现货-PLC编程器

返回列表页

参考价

面议

具体成交价以合同协议为准

产品型号flashpro5 usb下载线

品牌

厂商性质经销商

所在地深圳市

在线询价收藏产品

联系方式：雷俊查看联系方式

更新时间：2017-06-08 11:03:54浏览次数：335次

联系我时，请告知来自仪表网

产品分类 品牌分类

  电子元器件

集成电路IC

暂无信息

深圳博瑞图电子科技有限公司

经营模式：经销商

商铺产品：47条

所在地区：广东深圳市

联系人：雷俊（销售经理）

询价 给他留言

产品简介

全新美国*Microsemi flashpro5 usb下载线现货
FlashPro5 Device Programmer Quickstart Card

This quickstart card applies only to the FlashPro5 device programmer.

Kit Contents

QuantityDescription

详细介绍

全新美国*Microsemi flashpro5 usb下载线现货

FlashPro5 Device Programmer Quickstart Car

This quickstart card applies only to the FlashPro5 device programmer.

Kit Contents

Quantity	Description

1	FlashPro5 programmer standalone unit

1	USB A to mini-B USB cable

1	FlashPro5 10-pin ribbon ca

Software Installation

FlashPro or FlashPro Express software is automatically installed as part of the Libero^® System-on-Chip (SoC) software. If you are using the FlashPro5 device programmer for standalone programming or on a dedicated machine,

download and install the latest release of the FlashPro or FlashPro Express from the Microsemi^® website. The installation will guide you through the setup. Complete the software installation before connecting the FlashPro5

device programmer to your PC.

Note: The minimum version requirements to run FlashPro5 on Windows are Libero SoC v11.3/ FlashPro v11.3 and on Linux are Libero SoC v 11.4/ FlashPro v11.4:

www.microsemi。。ｃｏｍ/products/fpga-soc/design-resources/programming/flashpro

Hardware Installation

After installing the software successfully, connect one end of the USB cable to the FlashPro5 device programmer and the other end to your PC’s USB port. The Found Hardware Wizard will open twice. Use the wizard to install the driver automatically (recommended). If the Found Hardware Wizard cannot find the drivers automatically, then ensure you have properly installed the FlashPro software prior to installing the hardware. If the drivers still cannot be installed automatically, then install them from a list or specific location (advanced).

If FlashPro was installed as part of the Libero SoC default installation, the drivers are located at C:/Libero/Designer/Drivers/Manual. For a standalone Libero SoC FlashPro default installation, the drivers are located at C:/Microsemi/FlashPro_<ver>/Drivers/. Microsemi recommends the automatic driver installation.

Pin 4 on FlashPro5 programmers MUST NOT be connected or used for anything other than its intended purpose.

Common Issues

If the On LED does not light up after FlashPro5 driver installation, the driver might not be installed correctly and you must troubleshoot the installation. For more information, refer to the FlashPro Software and Hardware Installation Guide and the “Known Issues and Workarounds” section of the FlashPro software release notes: www.microsemi。。ｃｏｍ/products/fpga-soc/design-resources/programming/flashpro.

FlashPro5 may not operate correctly if pin 4 of the JTAG connector is improperly used.

Documentation Resources

Refer to the FlashPro software page for further information:

www.microsemi。。ｃｏｍ/products/fpga-soc/design-resources/programming/flashpro

Technical Support and Contacts

Technical support is available online and by .To find your local representative visit Microsemi SoC Sales offices, including Representatives and Distributors which are located worldwide.