行业产品

  • 行业产品

江苏春晨电缆有限公司


当前位置:江苏春晨电缆有限公司>>充电桩电缆>>EV-SS充电桩电缆>>EV-SS充电桩电缆-电气设备用电缆

EV-SS充电桩电缆-电气设备用电缆

返回列表页
参  考  价面议
具体成交价以合同协议为准

产品型号

品       牌

厂商性质生产商

所  在  地淮安市

联系方式:赵礼春查看联系方式

更新时间:2018-03-25 06:11:38浏览次数:570次

联系我时,请告知来自 仪表网

产品简介
产地 国产 护套材质 橡胶
加工定制 外表材质 PE
线芯材质 紫铜线 颜色 黑色
应用范围 电力系统    

江苏春晨电缆有限公司EV-SS充电桩电缆,热塑性弹性体绝缘热塑性弹性体护套电动汽车传导充电系统用电缆

详细介绍

进入公司商铺江苏春晨电缆有限公司EV-SS充电桩电缆,热塑性弹性体绝缘热塑性弹性体护套电动汽车传导充电系统用电缆,

(1) mixing

1、氯化聚乙烯的主链不含双键,机械塑料时主链不易切断,对其门尼粘度几乎没有影响,因此无需塑炼。

1, the backbone of chlorinated polyethylene containing double bond, mechanical plastic backbone is not easy to cut, almost no influence on the Mooney viscosity, so no plastication.

2、CPE胶既适宜开炼机混炼,又适宜密炼机混炼。用开炼机混炼之前,由于CPE为粉状,需先将CPE在70℃至90℃开炼机上薄通塑炼成半透明状,再进行混炼。CPE胶用密炼机混炼时,混炼胶的温度应控制在130℃~150℃范围为宜。如果将过氧化物直接加到密炼机中进行混炼,则密炼机温度要控制在过氧化物"起硫"温度以下。另外,CPE胶用密炼机混炼时,应有足够的装胶容量,一般应在95%以上。

2, CPE glue is suitable for mixing machine, but also suitable for mixing mixer. Before mixing with the mixer, due to the CPE powder, the need for the first CPE in 70 to 90 degrees Celsius on the mixer to thin plastic into a translucent, and then mixed. When the CPE glue is mixed with a mixer, the temperature of the mixture should be controlled in the range of 130 DEG C to 150 C. If the peroxide is directly added to the mixer for mixing, the temperature of the mixer is controlled below the temperature of the peroxide. In addition, CPE glue mixer mixing, there should be enough capacity to install glue, generally more than 95%.

(二)挤出

(two) extrusion

CPE抗焦烧性良好,可以挤出表面光滑的线缆产品。挤出机螺杆长径比小于12时,挤出有相当的难度。采用热喂料挤出,可改善线缆表面质量。当长径比大于12时,冷挤、热剂均能挤出表面光滑的线缆。在挤出温度方面由于CPE流动性不如CR好,塑化不易,因此在挤出时,机身温度控制在75℃~85℃;机头温度控制在85℃~95℃为宜。EV-SS充电桩电缆

CPE good scorch resistance, can squeeze out the smooth surface of cable products. Extrusion screw length diameter ratio is less than 12, extrusion is quite difficult. Hot extrusion can improve the surface quality of cable. When the ratio of length to diameter is greater than 12, the cold extrusion and heat agent can extrude smooth cables. In the extrusion temperature due to the CPE mobility is not as good as CR, plasticizing is not easy, so in the extrusion, the temperature of the body is controlled at 75 DEG C to 85 DEG C; the head temperature control in the temperature of 85 DEG C to C.

(三)硫化

(three) vulcanization

CPE适用于管道连续硫化。为了保证生产效率,提高硫化温度是必要的,一般在1.2~2.0MPa蒸汽压力下可连续硫化。温度过低,硫化体系用量不足或者水冷却段太短或无水冷却段,则易产生气泡。另外,CPE属于热敏性材料,在挤出和硫化阶段都应控制温度,温度过高,则易产生气孔。

CPE suitable for continuous vulcanization. In order to ensure the production efficiency, it is necessary to improve the curing temperature, which can be cured at 1.2 ~ 2.0MPa steam pressure. If the temperature is too low, the dosage of the curing system is insufficient, or the water cooling section is too short or the water cooling section is not enough, the bubble is easy to generate. In addition, CPE belongs to the heat sensitive materials in extrusion and curing stage should

关键词:开炼机 挤出机

感兴趣的产品PRODUCTS YOU ARE INTERESTED IN

仪表网 设计制作,未经允许翻录必究 .      Copyright(C) 2021 https://www.ybzhan.cn,All rights reserved.

以上信息由企业自行提供,信息内容的真实性、准确性和合法性由相关企业负责,仪表网对此不承担任何保证责任。 温馨提示:为规避购买风险,建议您在购买产品前务必确认供应商资质及产品质量。

会员登录

×

请输入账号

请输入密码

=

请输验证码

收藏该商铺

登录 后再收藏

提示

您的留言已提交成功!我们将在第一时间回复您~