缸体执行机构
Cylinder Actuators

　　空气或燃气缸体执行机构包括单动或双动，由机械弹簧或气动力实现故障开启或关闭等各种类型。空气缸体执行机构的局限性在于机械弹簧的局限性和要求推力不超过75,000磅。空气缸体执行机构所采用的机械弹簧可以达到20,000磅的推力，及Z大14英寸的冲程限制，主要取决于所需要的输出推力。
　　Air or gas cylinder actuators include single or double acting, fail open or closed by mechanical spring or pneumatic force. They can be manufactured to accommodate any length stroke. The limitations of air cylinder actuators are mechanical spring limitsthrust requirements in excess of 75,000 Ibs. Mechanical springs used with air cylinders can be sized for up to 20,000 Ibs. of thrusthave a stroke limit of about 14" max. depending on thrust output required.
　　对于有些无法采用机械弹簧的应用场合，可以配置气动弹簧，以储备足够实现故障安全功能的气源压力。大于25,000磅的推力要求可以通过配置标准镗孔的缸体执行机构来实现，在此假定现场气源压力Z小为80 PSIG。在25,000磅至75,000磅之间的推理要求可以通过对现场气源进行增压或加强，使其有更的工作压力来满足缸体执行机构的要求，并储存在当地的压气罐内。
　　In applications where mechanical springs can not be used, a pneumatic spring provided with stored air pressure is capable of providing a fail safe mode. Thrust requirements up to 25,000 Ibs. can be accommodated with standard bore size cylinders assuming minimum 80 PSIG field air supply. Thrust requirements between 25,000 Ibs.75,000 Ibs. can be accommodated by boosting or intensifying field air pressure to a higher working pressure for the cylinderstored locally in a high pressure air tank.
　　对于超过75,000磅的推力要求，液动系统会更加适合，也更加经济。缸体执行机构可以配置针对紧急状态下的手动过载装置，阀门驱动，故障安全功能和其它附件。
　　Hydraulic systems are better suitedmore economical for thrust requirements over 75,000 Ibs. Cylinder actuators can be provided with manual overrides for emergency valve actuation, fail safe modeother accessories.

隔膜执行机构
Diaphragm Actuators

　　隔膜执行机构适用于：双动气压开启或关闭，直接作用气压关闭，机械弹簧开启或反向作用机械弹簧关闭，气压开启。
　　Diaphragm actuators available are: double acting air pressure required open or close, direct acting air pressure required to close, mechanical spring to open or reverse acting mechanical spring to close, air pressure required to open.
　　这是一种很简单也很经济的执行机构，但是应用的局限性也比较大。*种局限在于冲程，对于大多数制造商来说，4英寸就是Z大的冲程。这种局限性使得隔膜执行机构只能适用于通径DN100以下的闸阀和更小通径的截止阀。第二种局限性在于输出推力，这是无法为我们的不平衡旋塞截止阀选择这种执行机构的主要原因。大多数制造商可以提供面积达到200平方英寸的隔膜，但是，可用于执行机构的Z大气源压力却在递减。大多数主要制造商提供的大面积隔膜的Z大气源压力小于45 PSIG，因此限制了推力的输出。作为选配件，可提供手动过载手轮。
　　This very simplevery economical actuator has application limitations. The first limitation is stroke; a 4" stroke is the longest available from most manufacturers. This limits adaptable valve size to gate valves 4"smallerglobe valves in smaller sizes. The second limitation is output thrust, this is the major constraint in selecting this type of actuator for use with our unbalanced plug globe valves. Most manufacturers can provide diaphragm areas up to 200 square inches, however, maximum air pressure allowed for actuation decreases. Maximum air pressures are as low as 45 PSIG for large area diaphragms available from most major manufacturers thus limiting thrust output. Manual override handwheels are available as an option.

1. 阀门通径，型号或规格说明。
   Valve size, figure number or description.
2. 操作条件压力，温度，流量和流体介质。
   Operating conditions pressure, temperature, flow ratefluid.
3. Z大关闭压差。
   Maximum differential shut-off pressure.
4. 主要动力供应 - 空气或液体 - 可提供的Z大和Z小压力和动力源。
   Primary power supply—air or hydraulic—available maximumminimum pressuresource.
5. 故障处理模式开启，关闭？
   Failure mode open, closed, as is?.
6. 控制电压和外壳结构NEMA，等等。
   Control voltageenclosure designations NEMA, etc..
7. 辅助设备：
   Auxiliary equipment:
   1. 限制开关，
      limit switches,
   2. 电磁阀，
      solenoids,
   3. 定位器，
      positioners,
   4. 手动过载装置
      manual over-rides.
8. 阀门定位。
   Valve orientation.
9. 如果有的话，所偏爱的制造商。
   Preference for specific manufacturer, if any.