上海荣计达ZW04砌墙砖成型试模厂家 二次成型试模价格

砌墙砖成型试模是检测仪器，用于工业与民用建筑砌墙砖抗压强度试验试样制备，使用前务必仔细阅读说明书。并由实验人员操作，以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。

The wall brick forming test mold is a testing instrument for the preparation of compressive strength test samples of industrial and civil building wall bricks. Please read the instructions carefully before use. It is operated by experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.

砌墙砖成型试模符合GB/T 2542-2012《砌墙砖试验方法》和GB/T 25044-2012《砌墙砖抗压强度试样制备设备通用要求》标准中抗压强度试验方法要求，分一次成型模具和二次成型模具两种。

The test mold for forming brick wall bricks complies with the requirements of compressive strength test methods in the standards of GB / T 2542-2012 "Test methods for brick wall bricks" and GB / T 25044-2012 "General requirements for equipment for preparing compressive strength samples for brick wall bricks". There are two types of primary mold and secondary mold.

砌墙砖成型试模尺寸：

1、一次成型试模组装后型腔尺寸为：长120mm±15mm（可调节）； 宽120mm±10mm（可调节）；高115mm±5mm

2、二次成型试模组装后型腔尺寸为：长240mm±15mm（可调节）； 宽120mm±10mm（可调节）； 高65mm±5mm

Brick wall mold test mold size:

1. The size of the cavity after the one-shot test mold assembly is: 120mm ± 15mm (adjustable); 120mm ± 10mm (adjustable); 115mm ± 5mm

2. The size of the cavity after the secondary molding test mold assembly is: 240mm ± 15mm (adjustable); 120mm ± 10mm (adjustable); 65mm ± 5mm

砌墙砖成型试模使用方法：

1、一次成型试模组装后，用润滑油进行抹刷，然后把砖试样放入试模中，在中间和两边插入插板以确定厚度，前后方向用胶皮密封，初步拧紧螺丝固定试样，取出插板，A终拧紧螺丝。把固定好样品的试模放到振动台上加入专用净浆制样。

2、二次成型试模组装后，用润滑油进行抹刷，放入专用净浆材料，然后把砖试样放入试模中的顶丝上，顶丝保证净浆厚度不超过3mm，用螺丝把试样固定，放到振动台上进行振动，待净浆材料硬化后拆模重新对另一面进行加工。

How to use the wall mold forming test mold:

1. After the molding test mold is assembled once, wipe it with lubricating oil, then put the brick sample into the test mold, insert the insert plate in the middle and both sides to determine the thickness, seal it with rubber in the front and back direction, and tighten the screw to fix the test In the same way, remove the plug-in board, and finally tighten the screws. Put the fixed mold on the shaking table and add special pure slurry to prepare the sample.

2. After the secondary molding test mold is assembled, wipe it with lubricating oil, put in special cleansing material, and then put the brick sample on the top wire in the test mold. The top wire ensures that the thickness of the clean pulp does not exceed 3mm. Fix the sample with screws, place it on a shaking table, and shake it. After the paste material is hardened, remove the mold and process the other side again.

砌墙砖成型试模保养：

试模使用结束后，把试模表面用铲刀清理干净，然后用润滑油进行涂涮，以方便下次使用。

Maintenance of molding test molds for masonry bricks:

After using the test mold, clean the surface of the test mold with a spatula, and then coat it with lubricating oil to facilitate the next use.