二、温控系统：
1、温度范围：室温—250度（可任意设定所需温度）
2、温控制器：采用RKC 70型温度控制器，LED做数字显示
设定，PID自动演算修正设定，配0.6芯电热偶及接触器输出
从而保证温度控制更加稳定和更精准。
3、温度器精度：±5℃
4、温度均匀度：±5℃（加热空炉上中下测试）
5、加 热 器：采用Φ11mm散热式干烧型发热管（采用进口的电阻丝及高温石
英砂制作），发热管装置在炉内两旁
三、运风控制系统：
1、运风电机：1台加强轴型烤箱专用电机及配置强力型多翼风轮
2、运风方式：在炉体两侧强制出风，顶部回风循环。
在炉体顶部配置排气排风烟囱，让产品在烘烤时，及时排出废气烟雾
四、炉体结构及用料：
1、炉体设计成：单开门。
2、内箱采用0.8mm不绣钢板制作。
3、外箱采用1.mm厚A3冷板加工成型后防锈处理，喷电脑白色。
4、保温材料:采用西斯尔80K环保高温棉，保温厚度为80mm
5、门边密封：采用耐高温硅胶迫紧密封
五、控制电器使用材料：
温度表：1个（中国台湾RKC）
电热偶：1条（0.6芯K型）
时间制：1套（够温计时）
运风电机: 1台（600W）
运风风轮: 1个12寸
接触器: 1套（10A）
电源开关： 1个（12A）
电源、加热、计时、控制扭制、开关各 ： 1套
六、安全体统：
1、电机缺相过流保护装置，（电机过载时，切断加热电源，防止烤坏产品）
2、控制回路短路及过载保护,当电路短路或其它故障时切断电源,保护电机安全
七、机台工作原理：
1、启动电源开花关→2、开启电机运风开关→3、开启加热开关→4、设置所
需温度→5、开始加热→6、温度到达开始自动计算烘烤时间→7、到达烘烤时间开始蜂鸣提示，并切断加热电源。
Ii. Temperature control system
1. Temperature range: room temperature -- 250 ° c (the required temperature can be arbitrarily set)
2, temperature controller: RKC 70 temperature controller, LED digital display
Set, PID automatic calculation and correction set, with 0.6 core electrothermal couple and contactor output
To ensure more stable and accurate temperature control.
3. Accuracy of the thermostat: ±5℃
4. Temperature uniformity: ±5℃ (upper, middle and lower test of heating empty furnace)
5, add heat exchanger: adopt Φ 11 mm cooling type dry type heat pipes (high temperature and the resistance of the wire imported stone
The heating pipe is arranged on both sides of the furnace
Iii. Transportation risk control system:
1. Wind motor: a special motor for strengthening shaft type oven and a powerful multi-wing wind wheel are equipped
2. Mode of air transportation: forced air out on both sides of the furnace body and air back circulation on the top
At the top of the furnace body is equipped with exhaust chimney, so that when the product is baking, exhaust fumes can be discharged in time
Iv. Furnace structure and materials:
1. The furnace body is designed as: single door.
2. The inner box is made of 0.8mm unembroidered steel plate.
3. The outer box shall adopt 1. Mm thick A3 cold plate for rust prevention after forming, and spray the computer white.
4. Thermal insulation material: it is made of CSR 80K environmental friendly high temperature cotton with a thermal insulation thickness of 80mm
5, door side seal: high temperature resistant silicone forced tight seal
5. Materials for controlling electrical appliances:
Temperature meter: 1 (Taiwan RKC)
Electric couple: 1 (0.6-core k-type)
Time system: 1 set (enough temperature timing)
Wind motor: 1 set (600W)
Wind turbine: 1 12"
Contactor: 1 set (10A)
Power switch: 1 (12A)
Power supply, heating, timing, control twist, switch: 1 set
Vi. Safety system:
1. Motor phase loss over-current protection device (when the motor is overloaded, cut off the heating power to prevent the product from being damaged)
2, control circuit short circuit and overload protection, when the circuit short circuit or other faults cut off the power, to protect the safety of the motor
Vii. Working principle of the machine:
1, start the power off →2, open the motor air switch →3, open the heating switch →4, set the station
Required temperature →5, start heating →6, automatically calculate the baking time when the temperature reaches the beginning →7, start beeping when the baking time reaches, and cut off the heating power
